Cod eroare Indesit


Indesit Washing Machines and Washer Dryers
• F10 – No cold fill. Check that the taps are on or if the drain hoses are kinked.
• F11 – No hot fill. The ambient temperature is likely to be below freezing possibly due to the pipes being
frozen. Also check that the taps are on or if the drain hoses are kinked.
• F12 – No mixed fill. It is likely that the water is not turned on at the taps.
• F13 – Check the water supply, inlet valve and hot and cold hose connections.
• F14 – A fault with the water heating has occurred.
• F15 – Water is not being pumped out and a flood condition could occur. Check that the drainage hose is
raised to the recommended minimum height and that the pipe is not blocked.
• F16 – Extremely high water level Disconnect or turn off the water supply and ensure that the water level
does not rise any more.
• F17 – Door not closed properly. Close door firmly at the 3 o’clock position.
• F20/1 – The thermistor resistance has drifted or the temperature scanning sequence is incorrect. The ambient temperature could be below freezing.
• F30/31 – A motor drive problem has occurred. Try running the programme again.
• F40 – Water below protection level during a heat step.
• F41 – Water level detect sequence incorrect.
• F50/51 – Customer language and wash programme have not been saved.
The system will run with default conditions (1000rpm max and English language). Book an indesit service engineer to reprogramme
your product.

Indesit Fridges
• F1 – Freezer thermistor open circuit.
• F2 – Freezer thermistor short circuit.
• F3 – Fridge thermistor open circuit.
• F4 – Fridge thermistor short circuit.
• F7 – Evaporator thermistor open circuit.
• F8 – Evaporator thermistor short circuit.
• F9 – Temperature set switch open circuit.
• FA – No feedback from Baffle.
• FB – Fridge Baffle motor operating continuously.
• FE – Defrost time out

Indesit Dishwashers
• F10 – Fill or empty time out. Check that the hoses are not kinked, that the taps are on or whether the drain pump or hose is blocked.
• F11 – Heater timed out. The heater has not reached the required level.
• F20 – Temperature under range.
• F21 – Temperature over range.

Fault codes for Indesit LCD Dishwasher Models
• A01 – Float switch operated.
• A02 – Open/Short circuit heater relay.
• A03 – Short circuit on thermistor.
• A04 – Unable to reach or sense temperature within 70 minutes.
• A05 – Pressure switch has not been reset.
• A07 – Open/Short circuit wash motor triac.
• A08 – Open/Short circuit auxiliary wash motor triac.
• A09 – Open/Short circuit with main wash triac.
• A10 – Open/Short circuit fill valve triac.
• A11 – Half load valve triac or alternating motor action.
• A12 – Open circuit heater rely.
• A13 – Open/Short circuit dispenser triac.
• A14 – Drain hose too low causing syphoning. Check drain hose and re-adjust.
• H20 – Check tap and pressure of incoming water.

Fault codes for Indesit LCD Tumble Dryers
• F01 – Short circuit motor triac.
• F02 – Motor jammed or fan blocked.
• F03 – Front thermistor open/short circuit.
• F04 – No pump piloting.
• F05 – No feedback from the pump.
• F08 – Static heater relay with contact welded closed.
• F09 – Eprom is not programmed or not functioning.
• F10 – Common of heater open or one shot open.
• F11 – No pump connection.
• F12 – Communication error between boards.
• F13 – Rear thermistor open/short circuit.
• F15 – Dynamic heater relay with contact welded closed.
• F-17 – Mater relay welded closed.

Fault codes for Indesit LCD EVO1 Washing machines and washer dryers
• F01 – Short circuit motor triac.
• F02 – Motor jammed tacho detached.
• F03 – Wash thermistor open/short circuit.
• F04 – Pressure switch jammed on empty.
• F05 – Pressure switch jammed on full.
• F06 – Program selector error.
• F07 – Heater relay stuck.
• F08 – Heater relay cannot be activated.
• F09 – Incompatible Eprom.
• F10 – Pressure switch not sensing correctly.
• F11 – Pump cannot be activated.
• F12 – Communication error.
• F13 – Dryer fan or dryer thermistor faulty.
• F14 – Dryer element faulty.
• F15 – Dryer element relay faulty.
• H20 – Not fillings. Check tap, hose and inlet valves.
• LOCKED – Check interlock.

Fault codes for Indesit LCD EVO2 and V4 washing machines and washer dryers
• F01 – Motor triac short circuit.
• F02 – Motor jammed or tacho detached.
• F03 – Wash thermistor open/short circuit.
• F04 – Pressure switch jammed on empty.
• F05 – Pressure switch jammed on full – Check pump for blockages.
• F07 – Heater relay stuck.
• F08 – Heater relay stuck.
• F09 – Setup error.
• F10 – Pressure switch not sensing.
• F11 – Pump cannot be activated.
• F12 – No communication between cards.
• F13 – Drying thermistor open/short circuit.
• F14 – Drying element faulty.
• F15 – Dryer element relay fault.
• F17 – Interlock error.
• F18 – Communication error.
• H20 – Not filling. Check tap, hose and inlet valves.

Indesit Tumble Dryers
• F1 – The level of required dryness has not been reached within the time period. Check that the correct
programme has been selected.
• F2 – Thermistor or sensing circuit failure.
• F3 – Heater plate over temperature. Check the filter and vent hose for a possible blockage.

Informatii Contact

 
0721217518 - VODAFONE 
0760132131 - COSMOTE
0747169947 - ORANGE
021 4250486 - ROMTELECOM
FAX 021 4232633 - ROMTELECOM
Program: Luni - Vineri 700 - 2000
Sambata 800 - 1700
In afara orelor de program puteti face o PROGRAMARE ONLINE 
Zona de acoperire BUCURESTI si ILFOV Deplasarea si Constatarea GRATUITE

Punct de lucru

reparati masini de spalatVizualizati Strada Bârlea nr.4 , Bucuresti
Atelierul este vis-a-vis de Electromagnetica din Calea Rahovei. langa McDonald's Trafic Greu

Despre noi

S.C. GENERAL WASH SERVICE S.R.L.

Sediu social: Str. Barca nr. 8, Bucuresti
Punct de lucru: Str. Barlea nr. 4, Bucuresti
Cod Unic de Identificare: 32372509
Nr. Registrul Comertului: J40/12925/18.10.2013
Telefon: 0721217518

Tipul de activitate, conform clasificarii CAEN  Repararea aparatelor electrice de uz casnic